This function (output 9/15 brown wire,
Imax = 100 mA)
can operate in three modes:
Mode 1. Immobilizer - constant minus when
dialing a combination of buttons
При нажатии ранее запрограммированной последовательности комбинации кнопок в автомобиле (коды которых есть в CAN-шине*) формируется постоянный «минус» на выходе модуля, что позволяет реализовать противоугонную
When
you press a previously programmed sequence of a combination of
buttons in the car (the codes of which are in the CAN-bus *), a
constant "minus" is formed at the output of the module, which makes
it possible to implement anti-theft blocking.
Programming a combination of buttons
After
entering the program number for a / m **, you must turn on the
ignition and enter program No. 1999 or press the gas pedal 10 times.
If everything is done correctly, then at the end of the procedure
for entering the programming mode, the LED LED will light up
constantly. Next, while the LED is on, enter the desired key
combination sequence. When the buttons are pressed, the LED will go
out, confirming that the module "sees" them. It is possible to
program up to 16 keystroke combinations, and one key can be pressed
several times. For example: book. Window regulator - 1 time, book.
Volume - 4 times, book. Hand brake - 3 times, etc. After entering a
combination of buttons, while the LED is on, turn off the ignition.
Reprogramming a combination of buttons
With
the ignition on, enter the previously programmed combination of
buttons, then carry out the learning procedure described in the
section "Programming a combination of buttons"
Deactivating the immobilizer
After
turning on the ignition and pressing the previously entered
combination of buttons, a constant minus will appear at the output
of the module, the direction indicators will flash 1 time ****.
Immobilizer activation
When
the driver's door is opened with the ignition off, the immobilizer
will automatically turn on, the constant minus will disappear at the
module output, the direction indicators will flash 2 times ****. If
the driver's door is not supported by the CAN bus, the immobilizer
will turn on immediately after the ignition is turned off.
Service
Mode
To
enter the immobilizer into the service mode, it is necessary to dial
the previously entered combination of buttons, and the last button
should be pressed and held for 5-6 seconds until the direction
indicators blink 5 times ****. Blocking will not work in this mode.
To
remove the immobilizer from the service mode (lock activation), it
is necessary to dial the previously entered combination of buttons,
and press and hold the last button for 5-6 seconds until the
direction indicators blink 1 time ****.
Mode 2. Pulse at the output when dialing a
combination of buttons
When
you press a previously programmed sequence of a combination of
buttons in the car (the codes of which are in the CAN-bus *), a
negative pulse of 1 second is generated at the output of the module.
This mode can be used to control the hood lock (opening), in the
driver identification system, etc.
Programming a combination of buttons
After
entering the program number for a / m **, you must turn on the
ignition, enter program No. 1987, then No. 1999. If everything is
done correctly, then at the end of the procedure for entering the
programming mode, the LED LED will light up constantly. Next, while
the LED is on, enter the desired sequence of the key combination.
When the buttons are pressed, the LED will go out, confirming that
the module "sees" them. It is possible to program up to 16 keystroke
combinations, and one key can be pressed several times. For example:
book. Window regulator - 1 time, book. Volume - 4 times, book. Hand
brake - 3 times, etc. After entering a combination of buttons, while
the LED is on, turn off the ignition.
Reprogramming a combination of buttons
With
the ignition on, enter the previously programmed combination of
buttons, then carry out the learning procedure described in the
section "Programming a combination of buttons"
Mode 3. Tracking button presses
When a
button is pressed in a car (the code of which is in the CAN bus *),
a negative signal is generated at the output of the module, the
duration of which is equal to the time the button is pressed. This
allows you to implement various anti-theft solutions using
third-party equipment.
Attention!
In most
cars, the module "reads" the foot and hand brake and this can lead
to malfunctions of third-party equipment. For example, if a lock is
made by the duration of pressing the button, then there is a
possibility that this duration will coincide with the duration of
pressing the brake pedal. To exclude a possible failure, the module
provides software disabling the definition of pressing the foot and
hand brakes. To do this, after entering the program number for the
car, you must enter the program No. 1986 (this program will disable
the detection of pressing the hand and foot brakes). To reset the
settings, simply re-enter the vehicle program number.
*
supported buttons are indicated in the
installation diagram
(icons below the table)
** the
program number is indicated in the
installation diagram
(in the table header)
***
instructions for entering the program number can be downloaded
here
****
not all vehicles can control direction indicators via the CAN bus.
In this case, the light indication will be by flashing the high beam
headlights or the high beam headlights together with the rear fog
lamps.